Filter Holders and Hardware

Merck Millipore All-Glass Filter Holder Kit

All-Glass Filter Holder Kit was designed for the filtration of aqueous and organic or corrosive liquids for particulate contamination analysis.

Merck Millipore Filter Holder Vacuum Manifolds

Provide vacuum support for simultaneous filtration of either three or six test samples

Merck Millipore Microfil™ Funnels

Available in different colors

Merck Millipore EZ-Fit™ Manifolds

General microbiological analysis

Merck Millipore Base and Cap for Vacuum Filtration with Glass Frit Support

Designed to replace parts contained in glass vacuum filtration kits or provide for an alternative configuration

Merck Millipore Glass Vacuum Filter Holder, 47mm

Includes 300mL funnel, fritted base and cap, clamp, and alignment sleeve. Glass Vacuum Filter Holders, 47mm are used in vacuum filtration of liquids to produce clarified or particulate-free filtrate or to analyze particulate or biological contamination retained on the filter surface.

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Fritted Glass Support and Ground Joint (47mm)

Recommended for routine filtration analysis of corrosive liquids and the removal of particulates from HPLC solvents

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Fritted Glass Support (25mm)

Designed to handle small volumes of liquids for analysis of particulate or microbiological contamination

Merck Millipore Swinnex™ Filter Holders

Ultraclean or sterilize small volumes of liquids dispensed by syringe

Merck Millipore Microfil™ Funnels and Filters

Presterilized, ready-to-use funnels and filter membranes

Merck Millipore Microfil™ Filtration System

Convenient filtration system uses presterilized funnels and membranes on lever-action filtration support

Merck Millipore Funnel, 300mL for 47mm Glass Vacuum Filter Holders

Replacement part for models XX1014700 / XX1014730 / XX1514700 vacuum filter assemblies. Funnel, 300mL for 47mm Glass Vacuum Filter Holders is a graduated funnel made of autoclavable borosilicate glass.

DWK Life Sciences Kimble™ Microfiltration Assembly Hardware

Use Kimble™ Microfiltration Assembly Hardware when filtering large volumes of viscous or proteinaceous solutions to give the maximum flow rate.

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Fritted Glass Support and Ground Joint (90mm)

Designed for large volume filtration analysis of corrosive liquids or samples with high particulate loads that would tend to clog a 47 mm diameter filter

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Stainless Steel Support and Ground Joint (90mm)

Recommended when filtering large volumes of viscous or proteinaceous solutions to give the maximum flow rate

Kontes™ Membrane Filtration Glassware from Restek

Used for routine filtration of corrosive liquids and removal of particles from HPLC solvents

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with PTFE-Faced Fritted Glass Support (47mm)

Used for autoclaving with the filter in place and is designed to handle up to 500mL of sample liquids for the analysis of particulate or microbiological contamination

Cole-Parmer™ Advantec 301900 Pressure Filtration Holder

Process samples from an in-line system or pressure vessel with this stainless steel holder. Cole-Parmer™ Advantec 301900 Pressure Filtration Holders maximize flow rates by applying positive pressure to the fluid over a broad membrane surface.

DWK Life Sciences Kontes™ Ultra-Ware™ Microfiltration Assembly with Stainless Steel Support and Ground Joint (47mm)

Recommended when filtering viscous or proteinaceous solutions to give the maximum flow rate

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Stainless Steel Support (47mm)

Designed to handle up to 500 mL of sample liquids for the analysis of particulate or microbiological contamination

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Fritted Glass Support (47mm)

Used for general filtration and is designed to handle up to 500mL of sample liquids for the analysis of particulate or microbiological contamination

DWK Life Sciences Kimble™ Kontes™ Component Parts For 47mm Ultra-Ware™ Microfiltration Assembly

For ultra-ware microfiltration assembly with stainless steel support

DWK Life Sciences Kimble™ Kontes™ Ultra-Ware™ Microfiltration Assembly with Stainless Steel Support (90mm)

Designed for large sample volumes or samples with high particulate loads that would tend to clog a 47mm diameter filter

Thermo Scientific™ Nalgene™ Polycarbonate Filling Bell

Transfer sterile media aseptically from large containers to small media bottles or culture vessels using the Thermo Scientifc™ Nalgene™ Polycarbonate Filling Bell.

  spinner